June 04, 2015

How to Select, Install Electric Fence

Advice from an electric-fencing expert on selecting and installing it for maximum security and safety for your horse. Plus, a maintenance checklist for you. By Bob Kingsbery with Sandra Cooke for Practical Horseman magazine.

By Bob Kingsbery With Sandra Cooke

When you need to build a new fence or replace an existing one, there's a major reason for using electric fence: Properly selected, installed and maintained, it's the most effective way to safely contain your horse. It's also economical and easy to install and maintain. Let's look at the basic components of an electric fence and how to avoid common problems.

Key Electric Fence Components
Charger. Sometimes also called an energizer or fencer, the charger needs to be powerful enough to deliver a definite jolt when your horse touches it, even when its current is reduced by vegetation touching the fence line or (as sometimes happens) by moist, dewy early-morning conditions.

Ignore chargers whose power is rated by miles; look instead for one rated by joules, a measure of the oomph with which the charger is pulsing its thousands of volts of current through the fence once every second. One joule is a minimum rating for fencing that encloses up to five acres, but I always recommend getting the most powerful charger you can afford. A higher joule rating doesn't mean the fence's jolt--which can't injure horses or other animals--will be harder or more painful, but that it will be more consistent.

The difference in cost will be insignificant compared to the value of your horses and your peace of mind; expect to pay $100 to $120 for a good one-joule charger that plugs into an outlet in the barn or elsewhere; six-joule chargers now sell for less than $200, a small premium for peace of mind. (Worried about your electric bill? Fence chargers use negligible amounts of power, whatever their rating.) I recommend solar-powered chargers--about three times as expensive as the plug-in type--only for paddocks where 110-volt power is unavailable; as well as delivering relatively low power for their cost, they're susceptible to failure.

It's possible to run insulated cable up to 1/4 mile from a charger to the fence without significant power loss. Install the charger under cover (except for solar-powered chargers, of course), where you can check it easily during each day's routine. Most chargers have a light that flashes with the electric pulse when they're plugged in and functioning.

Ground system. This is a series of three 6-foot-long, galvanized-steel rods pounded into the ground 10 feet apart and connected by insulated cable (see below) to the "ground" terminal on the fence charger. (In areas where soil is very dry, more than three rods may be needed.) Assuming that you have a good charger, the ground system is the key to your electric fence's effectiveness. If your horse touches the fence, he feels a jolt only when the brief pulse of electric current that goes through his body and into the ground is picked up by the ground system and returned to the fence charger, completing the circuit. Be sure to use a ground rod clamp to attach the ground wire as tightly as possible to the rod, rather than just wrapping it around.

Insulated cable. The cable that carries the electric pulse from the charger to the fence needs to be specifically for electric fence, with insulation rated for up to 20,000 volts (most fence chargers emit from 5000 to 10,000 volts)--the same degree of insulation as on automobile spark plugs. By using cable designed for electric fence, you avoid the electricity leakage that results when you connect the charger to the fence with heavy-duty household electric cable, whose insulation is rated for only 600 volts.

When attaching the cable to the fence itself, use a connector clamp rather than just wrapping the cable wire around the fence; cable connected by wrapping comes loose more easily or loses power due to oxidation or corrosion buildup. All fence manufacturers sell a connector clamp designed to work optimally with their product. You'll also need the cable to carry the electric fence current from one side of a gate to the other: Connect all strands of the fence to the cable on the side of the gate nearest the charger.

My preference is to then run the cable above the gate via an archway high enough to safely admit horses and paddock-maintenance equipment, but most people prefer to run the cable underground. That's fine as long as the cable is encased in waterproof plastic tubing, plugged at each end with silicone caulking and buried in an 18-inch-deep trench to protect it from damage by hooves and equipment. On the far side of the gate, use connector clamps to attach all strands of the fence to the cable.

Cut-off switch(es). Save lots of extra steps by installing a weatherproof knife-type cut-off switch (sold in the electric fence section of farm stores) between the insulated cable and its attachment to the fence, enabling you to turn the fence off without going back to the barn to unplug the charger. I also like to install cut-off switches on both sides of a gate--multiple cut-off switches allow you to isolate sections of the fence for easier trouble-shooting.

The fence itself. Visibility is key to an electric fence's effectiveness and safety. Materials such as 1.5- or 2-inch poly tape, braid, rope or coated HT wire make the fence easy for your horse to see and avoid. (Thinner fence materials such as poly wire or 1/2-inch poly tape are suitable for temporary installations or as a "hot wire" to keep horses away from solid fence; uncoated electrified wire--although dangerous when used as a fence material on its own--can also be used to protect solid fence.)
Choose a product with a long warranty (for instance, some fence materials have a guaranteed lifetime of 20 years) and follow the manufacturer's recommendations for number and spacing of strands. A good general rule of thumb is four to five strands of fence, 4 to 4.5 feet high, for perimeter fences and three to four strands for interior fences. Space the top two or three strands no more than 12 to 14 inches apart and the lower strands 18 inches apart, with the lowest strand 18 inches from the ground to minimize interference by grass and weeds.

Insulators. The type of insulator you need (to hold the fence material on the post that supports it, while preventing the fence from contacting any surface that will cause current to leak) is determined by your choice of electric fence; most manufacturers market insulators specifically suited to their fence products. In general, braid, rope, and coated wire are installed on insulators that allow the fence to slide through. To help prevent chafe and wear on a tape fence, however, insulators need to be the type that clamps and immobilizes the tape (especially important in windy areas), and to be installed vertically on the fence post. Avoid cheap "generic" insulators (often made of brittle plastic), which only last a few years.

Testing, Testing... Why It's Important
When your electric fence is built, monitoring its voltage regularly--I recommend daily--is a basic management practice, just like checking water buckets. Use a digital voltmeter that tells you exactly how many volts of current are on the fence. (How many volts are enough? Four thousand to 5,000--remember, there's no way this jolt of current can hurt your horse, but it needs to be definite enough for him to remember it and want to avoid it.)

Your first check of your new fence's voltage gives you a baseline so that future checks can alert you to voltage drops that signal problems. Depending on the strength of your charger, it will emit 6000 to 10,000 volts when nothing is connected to it. After you've hooked it to your fence, check the voltage at the furthest point from the charger. Some drop in voltage--1500 to 2000--is normal. A more than 2000-volt drop means either your charger is underpowered for the fence, vegetation or something else is "loading" the fence (touching it, causing voltage to leak away), there's a short-circuit somewhere in the system--or a combination of these.

If the base voltage on your newly built fence is 4000 or better and everything's working fine, watch on subsequent checks for an overall voltage drop of 1500 or more. (It's normal for voltage to be 500-1000 lower in the morning when moisture on the fence, posts, and nearby vegetation can cause temporary current leakage.) Such a significant decrease means it's time to check for problems and correct them before your horse discovers the fence no longer packs a punch; in fact, many horses can sense when the fence is or isn't functioning.

Electric Fence Maintenance Checklist
  • Look for and remove sources of "load." Mow or trim under bottom strand to prevent grass and weeds from touching the fence; watch for fallen limbs or other objects on the fence or caught in insulators. (Tips: Listen for the rhythmic snap that indicates a voltage leak; follow your ears to find the source. Drag a long stick on the ground beneath the bottom strand as you walk the fence-line; it may knock away an interfering object you don't even see.)

  • Check insulators. A broken insulator can allow the fence strand to touch the post--not an immediate problem with a nonconductive wood post, but if you're using steel T-posts a broken insulator can cause the fence to go dead when the strand touches the metal.

  • Check connections. Ground-rod wires can get knocked or kicked away. Wires attaching the cable to the fence may come loose.

  • Check the charger. A spider's web built between terminals can cause it to spark.

  • Check insulated cable. Look for places where the cable may be abraded, for instance where it passes through a hole cut in metal barn siding.

  • Check fence strands: Look for frayed spots in poly tape--if metal fibers in the weave become separated, tape can't conduct current.

  • Texas-based international fence authority Bob Kingsbery grew up on a family-owned horse-breeding farm; he has written widely on electric fencing and has conducted more than 300 seminars on fence technology and grazing management throughout the world. You can reach him with your electric-fence questions via email at bob@kingsbery.com.This story originally appeared in the March 2004 issue of Practical Horseman magazine
    - See more at: http://practicalhorsemanmag.com/article/electricfence_021005#sthash.eBjkBqW9.dpuf

    Leave a comment

    Comments have to be approved before showing up.